Joyetech - Atomizzatore Joyetech ProCore Remix RTA/RDA/Subohm

Joyetech ProCore Remix RTA/RDA/Subohm Atomizer

ProCore Remix è il primo Joye RTA / RDA. Può anche essere usato come atomizzatore sub-ohm, a seconda di quale preferisci. Con un sistema di serbatoio rigenerabile, puoi costruire bobine doppie o singole con l'aiuto del tappo. Essendo semplice e conveniente, l'enorme slot per flusso d'aria è pensato per una grande produzione di vapore e un sapore ottimale.

parametri
Serbatoio: 2 ml / 4,5 ml (escludere RDA)
Bobina: compatibile con le normali testine serie ProC
Discussione: 510 thread
 
Viene fornito con
1x atomizzatore ProCore Remix
1x tubo di sfiato prolungato
1x tubo di vetro da 2 ml
1x camera RTA
1x camera RDA
1x manicotto RDA
1x mazzo RTA / RDA
1x testa ProC1 (0,4ohm)
1x puro cotone
2x bobina Clapton
1x Avvio rapido
1x scheda di garanzia
1x scheda di avviso

 Una variabile del kit per quattro atomizzatori - RTA / RDA / 4,5 ml Subohm / 2 ml Subohm

A: Using as an RTA
1. Break down the atomizer and loosen the screws with the hex wrench.
2. Place the first coil into the post holes. 
3. Secure the coil in place and blend the excess wire outwards. 
4. Do the same with the second coil on the other side. (You can also choose to use single coil with the stopper.)
5. Tighten down the screws and make sure they're nicely secured. 
6. Snip off the excess wire. 
7. Straighten out the coils and make sure they're not touching the deck. 
8. Attach the atomizer base into your battery mod and press the fire button to heat the coil up to red. (Please wait until it cools down to avoid scorching. )
9. After the coil cools down, tear down a piece of pure cotton and place it into the coil carefully. 
10. Trim the cotton tight to the deck and push it back inside. 
11. Drip a few drops of e-liquids into the cotton to get it fully soaked and left it sit for a while. 
12. Install the chamber and screw the atomizer base back on. 

B: Using as an RDA
1. Break down the atomizer and loosen the screws with the hex wrench. 
2. Place the first coil into the post holes. 
3. Secure the coil in place and blend the excess wire outwards. 
4. Do the same with the second coil on the other side. (You can also choose to use single coil with the stopper.)
5. Tighten down the screws and make sure they're nicely secured. 
6. Snip off the excess wire. 
7. Straighten out the coils and make sure they're not touching the deck. 
8. Attach the atomizer base into your battery mod and press the fire button to heat the coil up to red. (Please wait until it cools down to avoid scorching. )
9. After the coil cools down, tear down a piece of pure cotton and place it into the coil carefully. 
10. Trim the cotton tight to the deck and push it back inside. 
11. Drip a few drops of e-liquids into the cotton to get it fully soaked and left it sit for a while. 
12. Put three O-rings into the grooves on the RDA sleeve separately.  
13. Install the RDA Sleeve and put the RDA chamber back on. 

C: Using as a sub-ohm atomizer (standard)
1. Break down the atomizer, unscrew the RDA/RTA deck and replace with the ProC head. 
2. Drip a few drops of e-liquid into the head. 
3. Screw the extended vent pipe onto the top cap. 
4. Put the standard glass tube on and install the whole atomizer. 

D: Using as a sub-ohm atomizer (2ml)
1. Break down the atomizer, unscrew the RDA/RTA deck and replace with the ProC head. 
2. Drip a few drops of e-liquid into the head. 
3. Put the 2ml glass tube on and install the whole atomizer. 

E-liquid filling for sub-ohm atomizers:
1. Aimed at the sign on top, push and pull the top cap to reveal the filling holes. 
2. Inject the e-liquid into the holes on both sides and close the top cap. 
3. Rotate the bottom airflow and inhale for a few times without pressing the fire button. 
4. Press the fire button and enjoy the flavor.